Currently we have Siedle Compact CA 812-1 Audio Set with a door station chime.
So i would like to check if its possible to change just the existing door bell communication
to Google Nest Doorbell(gen 2) with Battery using the chime wires. Any leads on how to setup this system.
Thanks in advance.
Related
I have a Jitsi instance that I would like to share with 50 people for an event. I will mute everyone to make sure that only one or two people are talking at the same time but I wonder if I need to ask people to cut the video too (which would be sad because seeing other people face would be fun).
I know that Jitsi works in peer to peer when only two people are connected but what about a larger room?
Does the server centralise all the video stream?
With more than two participants Jitsi Videobridge will take over (no peer to peer nor H264) and control video streams from clients to server to clients.
As far as I understand it works very much like a turn server.
It strongly depends on your hardware setup. If Jitsi is running on a dedicated machine it should be able to handle this.
On a virtual server on the other hand...
Is it possible to access my Cisco router details like Name,Model,IP Address,Connection status etc from my iOS mobile.
I'm even ready to write small mobile app in iOS to get all router details.
Since I have just started learning in iOS, don't know if any library already exists for above task.
If my router does not work or gets hang.. I even want to try for restart of router using my mobile.
If example code exist, it will be very useful.
Like Cisco already has andriod and iOS app for same above function but dont want to use this app and want to write my own app with limited features only.
(http://www.addictivetips.com/mobile/cisco-connect-express-manage-router-settings-remotely-android-ios/)
Thanks,
Accessing network gear is best done by using SNMP. Cisco has extremely rich management/monitoring capabilities via SNMP and all of their MIBs are publicly available here.
Almost all Cisco gear supports the SNMPv2-SMI MIB (the 1.3.6.1.2.1 OID) so querying things like sysName, sysLocation, sysContact, sysDescription, sysUpTime should be very easy. This MIB even supports tables for listing all the interfaces and IP addresses and has a whole lot of other things that might be of interest to you.
If you have SNMP write access on the device then you can even make config changes and perform management functions like rebooting or bringing an interface up/down.
There are a few SNMP libraries for ObjectiveC and I think Net-SNMP is the most popular (It's not .net even though the title suggests that).
If you are new to SNMP then I suggest starting simple by querying easy objects like 1.3.6.1.2.1.1.5 (sysName) and 1.3.6.1.2.1.1.6 (sysLocation) before trying to jump into tables like 1.3.6.1.2.1.2.2 (ifTable)
Remember, you don't have to stick with the standard MIBs you can download all of the custom ones that are particular to your device which will give you incredible amounts of flexibility.
You could use a screen-scraping technique to telnet or ssh to the Cisco device and parse the "show version" output. This will give you some of the information you need. For others, like IP addresses, you can use "show ip interface brief", "show cdp neighbors" etc. as you need.
Keep security in mind: make sure that telnet/ssh credentials are adequately protected in your app's settings, and try to restrict your commands to those that do not need privileged access on the Cisco device.
Be aware that Cisco devices have a small pool of available VTYs, and every telnet/ssh access from your app will use up one VTY. So if you have for example 30 guys wanting to use the access the device simultaneously from their apps, some of those instances are not going to get access to the device.
If this is a concern, SNMP is a better and more scalable option as suggested by previous answer. Make sure that you (a) have a read-only community string configured on the device, and (b) use only the ro community string from the app.
I want to be able to show (by device) open/blocked status for a given protocol between two devices/ports on a network. In other words, I need to output a list of network devices (firewalls & switches) between Server A and Server B and indicate whether the request should (according to each device's rules) be allowed through or blocked.
I'm starting with the Cisco networking devices, which are centrally managed by Cisco's Security Manager (CSM) application (version 4.2). I'm new to network management automation programming and want to make sure I'm not overlooking an obvious best way to handle this.
So far it's looking like I'll need to periodically export and ETL device rules out of CSM (they have a perl script that I can call to do this I believe) and into a separate database, then write some custom SQL code to determine which devices on a route between two hosts/ports will allow or block traffic of the given protocol?
Am I on the right track, or is there a better way to go about this?
If I understood your question, I think you can run a TCL script inside the Cisco equipments do collect the necessary information and transfer it to a central server, form there import it to a database and then correlate that information.
Hope that helps you in your work.
What would be the best way of sending a signal from an iPad to an Arduino?
I am trying to use XBee, with iPad and Arduino to send a wireless signal.
I want to make a big red virtual button on an iPad that, when pressed, turns on an LED on the Arduino.
I am a total newbie when it comes to iOS, but OK with Arduino and XBee.
So I'm not sure if I understood correctly, but in my meaning there is only one simple way to solve the problem:
Connect an XBee to a Computer and another to the Arduino. On the computer you launch a webserver, which will be accesible from the iPad over Safari. This server handles the clickes and writes to the XBee Com Port, for communication.
Here are some examples, people already made:
http://www.projectallusion.com/1/post/2009/11/iphone-controlled-solar-powered-arduino-tank.html
http://www.sparkfun.com/tutorials/152 (not with xbee, but you can implement that by yourself)
I know it's been a while but I just came across to this question and yesterday I was doing the exact same thing so I'll share the method I used and the source of it.
In order to set a LED on or off in an Arduino board from the iPad you really don't need anything more than a browser. This is of course if you have a way to connect that Arduino to the local network.
Today you have at least two options. The WiFi and the Ethernet shields. Once you have your Arduino board inside the network you can send the instructions (HIGH or LOW) to the board form the browser.
These are my two boards connected waiting to be plugged to the local network:
Of course, you'll have to code the board to process those instructions. There are many examples on how to configure network settings and state instructions:
If you have a bit of time and want to do something more elaborated you could create a simple app to graphically control the state of those LED(s).
Inside you'll basically do the same thing, create the URL command and send it to the Arduino IP but it'd look much nicer. If you integrate later more controls the sky in the limit.
My experiment is a combination of what I learned from this nice tutorial and some tips I've read here and there.
I hope it becomes also useful to someone else.
Cheers,
Since you need to use a network connection from the iPad, a possibly simpler way to do this would be to use a WiFi module on the Arduino to poll a web script, and have the iPad write a state (button press) to that web script.
There's a handy WiFi module called the RN-XV that's designed like an XBee. I wrote up two tutorials on it:
http://log.liminastudio.com/programming/getting-started-with-the-rn-xv-wifi-module-node-js
http://log.liminastudio.com/itp/physical-computing/using-the-rn-xv-wifi-module-as-a-remote-switch
Hie members! ----am Boniface M - - a beginner in android[University student]..
My question is am planning to develop an android app/middleware that will act as a grid service .i.e an app for grid computing.. the application needs to be installed in 1....n devices. in the connection, one device must act as a server for all others. communication between the devices is via the wifi under the permission of the server device.which is determined by a certain algorithm[no problem here].
The problem is should i use a database that will keep track of all the services a device is running which are accessible to other devices or is there any way that i can directly keep all this information and then retrieve them as i request them from another app installed in another device.
and also how i can share files via wifi like blutooth
Thanks....
You're asking many questions in one and I'm actually unsure what you mean overall. Here's a few links that are sure be of some use...
http://developer.android.com/reference/android/os/Build.html This library is good for finding out information about the device you're running on.
http://developer.android.com/reference/android/location/Criteria.html - Criteria might be useful, lets you know what location based services you have running
Other than that, if you're looking to see if particular things are running check out this question: How to check if a service is running on Android?
If you're looking to keep a central hub of what devices have what available etc. you're going to need a middle man for what you want to do I suspect. If it was me, I'd do HTTP requests to a server, to php scripts I have written which would then read/write from a MySQL database to get information about other devices.
If you want to share files via wifi.. you're going to need an FTP server on the phone. There's an app swiFTP which does this to some degree (phone -> PC) but the concept should be the same. Take a look at it. It's a starting point! http://www.tested.com/news/how-to-transfer-files-wirelessly-to-your-android-phone/53/
Again, I'm unsure EXACTLY what you're looking to do but hopefully all of that is of some help. If it's not leave me a comment and I'll try and assist you further.
hope it helps!