Hi I am using LabView 2012, Delphi XE7 and GPIB (I think 488.2), Win7 SP1 and Agilent 53131A.
I used the given NI examples.
NI Labview example - Found in LabVIEW's help - GPIB.vi.
I tried writing and reading to query frequencies from 2 channels and they are successful.
They are are sent and read in succession.
*IDN?
:FUNC 'FREQ 1'
:READ:FREQ?
If they are successful, that meant GPIB for Agilent and NI MAX and driver are successfully installed and configured.
I am also able to use KeySight Connection Expert's to write and read, Again it is also successful.
However, When I used the given NI example in Delphi. Orginally it was saved as Delphi 3 or 4.
I used the Scope Simple example for universal counter. I used it mostly for writing and reading in the simple way. All it needs initialization, read/write and cleanup
I changed the following codes as shown below, in SimpleForm.pas
The detected device is at GPIB0::3::INSTR so, at line 32,
PRIMARY_ADDR_OF_COUNTER = 3;
String to write and read so, at line 132,
CommandBox.Text := '*IDN?';
then it was compiled with no error and run.
String to write was successfully
But upon reading, it was not successfully.
The string output is supposed to be ' HEWLETT-PACKARD,53131A,0,4806'.
The error at the end of the program is as follows below:-
Unable to read from device
ibsta = SC000 <ERR TMO>
iberr = 6 <EABO>
ibcntl = 0
From these readings, I figured out as :-
EABO means abort
I am not familiar with working of GPIB. Kindly advise.
You are correct that EABO is the identifier for an abort. In addition, we can see from ibsta = SC000 <ERR TMO> that the cause of the abort was a GPIB timeout error. I am not familiar with Keysight Connection Expert or your instrument, but since the error was from GPIB timeout, the most likely causes are:
The query was improperly formatted and the instrument thought it was just a write statement with no response needed. (That's probably why the write function had no error, but the read function timed out.)
The query was improperly formatted and the instrument returned an error.
Instrument needs to have 'Talker' capability enabled to send data. (Most instruments do this automatically with queries.)
For more information on generic GPIB commands, see this reference from the folks at National Instruments.
We have been trying to make use of the RabbitMQ Service Bus (v3.3.4) but the central bus keeps crashing. At the moment we are not using any clustering and its hosted on Windows Server 2008 R2. We'd like to isolate the root cause but the below error is the only one we can find. Can anyone shed some light on what; if anything; we can do to find the root cause of this?
Note: There are roughly 20 consumers with roughly the same number of Topic subscriptions. Also, all the clients are .NET 4.5 using the 3.3.4 Rabbit client libraries.
Version=1
EventType=APPCRASH
EventTime=130658038736577295
ReportType=2
Consent=1
ReportIdentifier=7f93ccd8-9cbe-11e4-ae00-000c29c08139
IntegratorReportIdentifier=7f93ccd7-9cbe-11e4-ae00-000c29c08139
Response.type=4
Sig[0].Name=Application Name
Sig[0].Value=erl.exe
Sig[1].Name=Application Version
Sig[1].Value=0.0.0.0
Sig[2].Name=Application Timestamp
Sig[2].Value=5343035d
Sig[3].Name=Fault Module Name
Sig[3].Value=MSVCR100.dll
Sig[4].Name=Fault Module Version
Sig[4].Value=10.0.30319.1
Sig[5].Name=Fault Module Timestamp
Sig[5].Value=4ba220dc
Sig[6].Name=Exception Code
Sig[6].Value=40000015
Sig[7].Name=Exception Offset
Sig[7].Value=00000000000760d9
DynamicSig[1].Name=OS Version
DynamicSig[1].Value=6.1.7600.2.0.0.272.7
DynamicSig[2].Name=Locale ID
DynamicSig[2].Value=1033
DynamicSig[22].Name=Additional Information 1
DynamicSig[22].Value=8d79
DynamicSig[23].Name=Additional Information 2
DynamicSig[23].Value=8d79a00078e92d9c3d5d79d4324254fe
DynamicSig[24].Name=Additional Information 3
DynamicSig[24].Value=9af5
DynamicSig[25].Name=Additional Information 4
DynamicSig[25].Value=9af5b20633c279dbf44b04a614c6a1f6
UI[2]=C:\Program Files\erl6.0\erts-6.0\bin\erl.exe
UI[5]=Check online for a solution (recommended)
UI[6]=Check for a solution later (recommended)
UI[7]=Close
UI[8]=erl.exe stopped working and was closed
UI[9]=A problem caused the application to stop working correctly. Windows will notify you if a solution is available.
UI[10]=&Close
LoadedModule[0]=C:\Program Files\erl6.0\erts-6.0\bin\erl.exe
LoadedModule[1]=C:\Windows\SYSTEM32\ntdll.dll
LoadedModule[2]=C:\Windows\system32\kernel32.dll
LoadedModule[3]=C:\Windows\system32\KERNELBASE.dll
LoadedModule[4]=C:\Windows\system32\MSVCR100.dll
LoadedModule[5]=C:\Program Files\erl6.0\erts-6.0\bin\erlexec.dll
LoadedModule[6]=C:\Windows\system32\USER32.dll
LoadedModule[7]=C:\Windows\system32\GDI32.dll
LoadedModule[8]=C:\Windows\system32\LPK.dll
LoadedModule[9]=C:\Windows\system32\USP10.dll
LoadedModule[10]=C:\Windows\system32\msvcrt.dll
LoadedModule[11]=C:\Windows\system32\IMM32.DLL
LoadedModule[12]=C:\Windows\system32\MSCTF.dll
LoadedModule[13]=C:\Windows\system32\apphelp.dll
LoadedModule[14]=C:\Program Files\erl6.0\erts-6.0\bin\beam.dll
LoadedModule[15]=C:\Windows\system32\ADVAPI32.dll
LoadedModule[16]=C:\Windows\SYSTEM32\sechost.dll
LoadedModule[17]=C:\Windows\system32\RPCRT4.dll
LoadedModule[18]=C:\Windows\WinSxS\amd64_microsoft.windows.common-controls_6595b64144ccf1df_6.0.7600.16661_none_fa62ad231704eab7\COMCTL32.dll
LoadedModule[19]=C:\Windows\system32\SHLWAPI.dll
LoadedModule[20]=C:\Windows\system32\COMDLG32.dll
LoadedModule[21]=C:\Windows\system32\SHELL32.dll
LoadedModule[22]=C:\Windows\system32\WS2_32.dll
LoadedModule[23]=C:\Windows\system32\NSI.dll
LoadedModule[24]=C:\Windows\system32\IPHLPAPI.DLL
LoadedModule[25]=C:\Windows\system32\WINNSI.DLL
LoadedModule[26]=C:\Windows\system32\mswsock.dll
LoadedModule[27]=C:\Windows\System32\wshtcpip.dll
LoadedModule[28]=C:\Windows\system32\NLAapi.dll
LoadedModule[29]=C:\Windows\system32\DNSAPI.dll
LoadedModule[30]=C:\Windows\System32\winrnr.dll
LoadedModule[31]=C:\Windows\system32\napinsp.dll
LoadedModule[32]=C:\Windows\System32\wship6.dll
FriendlyEventName=Stopped working
ConsentKey=APPCRASH
AppName=erl.exe
AppPath=C:\Program Files\erl6.0\erts-6.0\bin\erl.exe
I'm currently working with tshark using python subprocess and I want to handle errors in the child process currently.
I can get the sub-process exit code via python's subproccess 'returncode' field, but I can't fined any documentation of tshark exit codes.
I already figured out that 0 means success (no surprise) and 2 means corrupt or unsupported file.
But where there is 0 and 2 there is usually a 1, and there should be more codes.
Does anyone know were I can fined a list of thsark's possible error codes and causes?
Ages ago, I seem to remember somebody suggesting an exit status of 1 for command-line syntax errors and 2 for other errors, and I've followed that convention for a lot of code I've written.
So 1 would be returned if you gave an invalid command-line flag or an invalid capture or display filter or something such as that, and 2 would be returned if it couldn't open a capture device or capture file.
I'm trying to use the Java API for Neo4j but I seem to be stuck at IndexHits. If I query the DB with Cypher using
START n=node:types(type="Process") RETURN n;
I get all 2087 nodes of type "Process".
In my application I have the following lines
Index<Node> nodeIndex = db.index().forNodes("types");
IndexHits<Node> hits = nodeIndex.get("type", "Process");
System.out.println("Node index size: " + hits.size());
which leads my console to spit out a value of 0. Here, db is of course an instance of GraphDatabaseService.
I expected an object that included all 2087 nodes. What am I doing wrong?
The .size() question is just the prelude to my iterator
for(Node process : hits) { ... }
but that does not much when hits.size() == 0. According to http://api.neo4j.org/1.9.2/org/neo4j/graphdb/index/IndexHits.html this should be possible, provided there is something in hits.
Thanks in advance for your help.
I figured it out. Man, I feel so embarrassed...
It so happens that I had set up the DB_PATH to my default data folder, whereas the default storage folder is the default data folder plus graph.db. When I tried to run the code from that corrected DB_PATH I got an error saying that a lock file was in place because the Neo4j server was running. After shutting it down it worked perfectly.
So, if you happen to see the following error, just stop the server and run the code again:
Caused by: org.neo4j.kernel.StoreLockException: Could not create lock file
at org.neo4j.kernel.StoreLocker.checkLock(StoreLocker.java:74)
at org.neo4j.kernel.StoreLockerLifecycleAdapter.start(StoreLockerLifecycleAdapter.java:40)
at org.neo4j.kernel.lifecycle.LifeSupport$LifecycleInstance.start(LifeSupport.java:491)
I found on several forums that you cannot run the Neo4j server and use the Java API to query it at the same time.
I am extremely new to Informix and am having some trouble trying to get sqldemo installed.
Set up so far:
openSuse 12.1 (32 bit)
Informix Growth Edition 11.70 UC6
Informix SQL Developer 7.50 UC6
Informix RDS 7.50 UC6
Informix ID 7.50 UC6
After struggling a few days and a lot of reading of http://publib.boulder.ibm.com/infocenter/idshelp/v117/index.jsp, I managed to get Informix installed and On-line.
I also opted to install the demo database instance that comes with the installation.
I now and attempting to get started with Informix 4GL by Example.
I am trying to get the sqldemo database up. I don't know if it will replace the previous instance installed with Informix, but that is a different problem.
Right now as per the document, running the following should set up the DB:
sqldemo stores2t -log
I however get an error: "Invalid Locales set !!".
I have tried looking up this error and also in the documentation.
I have tried setting the CLIENT_LOCALE and DB_LOCALE in my .profile file.
For example:
export CLIENT_LOCALE=en_US.CP1252 and
export DB_LOCALE=en_US.819
This has not helped.
A push in the right direction, or perhaps some other documentation I could read that would explain things better would really be appreciated.
If any other information is required from me, please do not hesitate to ask.
Update 1
Thanks so much for the response.
A couple of things firstly that I have tried since your post.
Changed the the CLIENT_LOCALE and DB_LOCALE as you specified - Same error - So i removed it as you said it should not be set.
Fixed a problem in my PATH and made sure it has /usr/informix/bin - Same Error
INFORMIXDIR is /usr/informix
INFORMIXSERVER is ol_informix1170 (This is from the database that was installed with the informix install, don't know if this must be changed? and if so to what?)
Ran the script you mentioned, result :
INFORMIXDIR=/usr/informix
INFORMIXSERVER=ol_informix1170
INFORMIXSQLHOSTS=/usr/informix/etc/sqlhosts
LANG=en_US.UTF-8
ONCONFIG=onconfig
I noticed I had set the language to UK, which made the Locales en_gb instead if en_us, so tried changing that in my .profile, which did not help, so also tried changing the language to US and the locales to en_us, but this made no difference.
As for what you said about the sqldemo script and the already installed db, It is fine if that db is removed as this is just a test VB box for me to learn on.
Could the $INFORMIXSERVER set as ol_informix1170 be the problem?
Thank you once again for the help.
Neill
Update 2
Thanks again for the response.
A few things to note.
The dbenv results I posted is all that shows which i assume/presume (uh-oh) means that the other environment variables are not set. Which of the environment variables you posted are absolutely necessary for it to work?
As above, Where would I find the terminfo file, or does this need to be created?
As above, the SQLEXEC variable... where would I find sqlrm? I can somewhat remember from the documents I have read I think it should be $INFORMIXDIR/lib? but I only have an esql directory. Is this correct.
Barring that something in the first 3 above is not causing more problems, when trying your suggestion of DEMOPATH=en_us/0333 sqldemo stores2t -log I receive the following error:
Sorry, cannot read the mkstores3 program required to build the demonstration database. Check the /etc subdirectory of INFORMIXDIR (/usr/informix).
Checking /usr/informix/etc shows indeed that there is no mkstores3 file.
Attempting your further note of isqldemo, I get the following error:
/usr/informix/bin/isqldemo: line 58: /usr/informix/demo/sql/en_us/e01c/isqldemo: No such file or directory.
I guess this makes perfect sense as there is no e01c directory, just the 0333 directory.
Right now anything you can tell me would indeed be a consolation because my newb-ness to generally Linux and definately Informix is a big factor. Interesting that this bug has been around for so long. I guess way more experienced folk than I figured out how solve it on their own, or just never bothered with the sqldemo.
I guess that will teach me to read this:
INFORMIX-4GL by Example
Version 4.1
July 1991
Going to check now if any updated text exists, but would still appreciated more help in solving this problem. Do you think reverting to a previous snapshot before Informix was installed and not opting for the ol_informix1170 database to be included could be a possible solution? I wouldn't really see that it would be, but what do I know.
Many many thanks for your continued time and effort.
Regards,
Neill
Update 3
So I see indeed the document I was reading is ancient. I have found an updated one (2002) which uses a different script (dbaccessdemo7).
I tried running that, have run into an error, but tomorrow is another day.
For now I am going to mark this as solved because of the bug detected and resolved. I am not going to put more time and effort into sqldemo.
Thank you so much, and if I struggle with dbaccessdemo 7, I will post a new question.
Regards,
Neill
The sqldemo script won't create a new server; it may clobber your existing database (a single server may house multiple databases; indeed, there are 4 sys* databases created when a server is initialized) but it won't harm your server otherwise.
Probable cause of the error
The normal problem with invalid locales is that you've not set $INFORMIXDIR. You need $INFORMIXDIR set unless /usr/informix is (a symlink to) the correct location. You also need $INFORMIXSERVER set, and you usually need $INFORMIXDIR/bin on $PATH. Strictly, $INFORMIXSERVER is the only mandatory variable; in practice, you worry about the other two too.
The $INFORMIXDIR setting is used to locate the locale information (which is found in $INFORMIXDIR/gls) and the message files (which are found in $INFORMIXDIR/msg).
Note that CP1252 is a Windows code page. Normally on Unix, you'd either not set CLIENT_LOCALE or DB_LOCALE, or you could set them to:
export CLIENT_LOCALE=en_us.8859-1
export DB_LOCALE=en_us.8859-1
or you can choose another more appropriate (to you) locale. The 8859-15 locale includes the Euro symbol, for example, or the utf-8 locale dictates UTF-8 in the database. But, for initial debugging, stick with the 8859-1 locale, aka 819 or 0333 (all based on the IBM CCSID). If it doesn't work with 8859-1, then we have one set of problems; if it works with 8859-1 but not some other codeset or locale, then we have a different set of problems.
Follow-up info if the solution above fails
If that isn't the trouble, then I'll ask for some more details — notably, your Informix environment as reported by the dbenv script below:
: "#(#)$Id: dbenv.sh,v 2.11 2007/09/02 00:18:58 jleffler Exp $"
#
# Printout INFORMIX database environment
informix1="DB[^=]|DELIMIDENT=|SQL|ONCONFIG|TBCONFIG|INFOR"
informix2="ARC_|CLIENT_LOCALE=|GL_|GLS8BITSYS|CC8BITLEVEL|ESQL|FET_BUF_SIZE="
informix3="INF_ROLE_SEP=|NODEFDAC=|ONCONFIG|OPTCOMPIND|PDQ|PSORT"
informix4="PLCONFIG|SERVER_LOCALE|FGL|C4GL|NE_"
informix5="TCL_LIBRARY|TK_LIBRARY"
informix="$informix1|$informix2|$informix3|$informix4|$informix5"
system="COLLCHAR=|LANG=|LC_|LD_LIBRARY_PATH(_64)?=|PATH=|SHLIB_PATH="
jlss="IXD(32|64)?="
env |
egrep "^($informix|$system|$jlss)" |
sort
It's an old script; that's why the shebang is missing.
Second set of diagnosis
I was hoping for the complete output of the dbenv script; it is surprising how often something shows up. However, given what you've said, it is likely to be OK.
The INFORMIXSERVER setting sounds fine.
I'm struck by the LANG=en_US.UTF-8 setting; Informix does pay attention to $LANG and the $LC_* variables (that's why dbenv prints those out). That may be a factor in the problem. However, I would have expected CLIENT_LOCALE and SERVER_LOCALE to deal with that if it was the problem. Also, on my Mac, I have LANG=en_US.UTF-8 and yet I can connect to (8859-1) databases OK.
This is beginning to look like an install problem...or sqldemo problem...
I transitioned from a Mac to a RHEL 5 (archaic) x86/64 machine, and tried running sqldemo over there:
$ dbenv
DBDATE=Y4MD-
DBEDIT=vim
INFORMIXDIR=/work4/informix/tools-7.50.FC4
INFORMIXSERVER=toru_31
INFORMIXSQLHOSTS=/work4/informix/ids-11.70.FC4/etc/sqlhosts
INFORMIXTERM=terminfo
IXD64=/work4/informix/ids-11.70.FC4
IXD=/work4/informix/tools-7.50.FC4
IXH=/work4/informix/ids-11.70.FC4/etc/sqlhosts
IXO=/work4/informix/ids-11.70.FC4/etc/onconfig.toru_31
IXS=toru_31
LANG=en_US.UTF-8
LD_LIBRARY_PATH=/lib64:/usr/lib64:/work4/informix/tools-7.50.FC4/lib:/work4/informix/tools-7.50.FC4/lib/tools:/work4/informix/tools-7.50.FC4/lib/esql:/work4/informix/ids-11.70.FC4/lib:/work4/informix/ids-11.70.FC4/lib/esql:/work4/informix/ids-11.70.FC4/lib/cli
ONCONFIG=onconfig.toru_31
PATH=/work4/informix/tools-7.50.FC4/bin:.:/work4/jleffler/bin:/u/jleffler/bin:/work4/informix/ids-11.70.FC4/bin:/u/jleffler/linux/x86_64/bin:/work4/informix/11.70.FC1:/usr/atria/bin:/work4/jleffler/perl/v5.12.1/bin:/usr/bin:/bin:/usr/X11R6/bin:/atria_release/cm_dist/vobs/imitools/bin:/opt/rational/clearcase/bin:/opt/rational/clearquest/bin
SQLCMDLOG=/work4/jleffler/.sqlcmdlog
SQLEXEC=sqlrm
TERMINFO=/work4/jleffler/terminfo
TERM=xterm-color
$ sqldemo st2 -log
Invalid Locales set !!
$
Oh yeah? No; my locales are fine, thank you!
Well, so be it...I can reproduce your problem! That's step 1. Step 2 is to look at the expletive deleted script.
PRODUCT=sql
DEMOFILE=sqldemo
DEFLANG=en_US.8859-1
INFORMIXDIR=${INFORMIXDIR:=/usr/informix}
INFENV=$INFORMIXDIR/bin/infenv
CONVLOC=$INFORMIXDIR/bin/convloc
if [ $# -gt 0 -a "X$1" = "X-e" ] ; then
LOCALE=$DEFLANG # -e means en_US.8859-1 required
shift
else
LOCALE=`$INFENV DBLANG` # get DBLANG value
if [ "x${LOCALE}" = "x" ]; then
LOCALE=`$INFENV CLIENT_LOCALE` # try CLIENT_LOCALE instead
if [ "x${LOCALE}" = "x" ]; then
LOCALE=`$INFENV DB_LOCALE` # finally default to DB_LOCALE
fi
fi
fi
if [ "x${LOCALE}" = "x" ]; then
LOCALE=$DEFLANG # finally default to DB_LOCALE
fi
export LOCALE
if [ "x${DEMOPATH}" = "x" ]; then
echo "Invalid Locales set !!"
else
exec $INFORMIXDIR/demo/$PRODUCT/$DEMOPATH/$DEMOFILE $*
fi
exit $?
Note that test for ${DEMOPATH}; note that DEMOPATH is not set in the script. So, we've got to get it set. What to? Well, ls $INFORMIXDIR/demo/sql shows that there are various locale-specific sub-directories (en_us,
ja_jp,
ko_kr,
th_th,
zh_cn,
zh_tw) and under the en_us directory there's 0333 (only).
Please run:
DEMOPATH=en_us/0333 sqldemo stores2t -log
This more or less worked for me — I believe it would work for you. I have a slightly unusual setup in that I have just I4GL (p-code and c-code) and ISQL in the $INFORMIXDIR; the server is run out of a different directory. This means I don't have server utility programs like dbload (specifically) in $INFORMIXDIR/bin. When the sqldemo script tried to load the data with dbload, therefore, it failed for me. It would work for you because you have all the Informix software in a single directory. To add insult to injury, it runs the dbload program by explicit path, so I can't futz my PATH to make it available.
This should get you going. I have a bug to report...it is CQ idsdb00244894.
I'm sorry that you ran into so much trouble. You shouldn't have done so.