there are very similar questions to this one but all of them are solved by disabling some other wifi source by using modprobe and then reseting rfkill
in my case:
artixlinux:[rail]:/etc/modprobe.d$ rfkill list all
0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: yes
and with nmcli:
wlan0: unavailable
"Qualcomm Atheros AR9485"
wifi (ath9k), 5A:9D:61:C0:BB:F0, sw disabled, hw, mtu 1500
I've already tried to modprobe ath9k but that does nothing
hardware:
[System]
OS: Artix Linux 20220123 n/a
Arch: x86_64
Kernel: 5.18.0-zen1-1-zen
Desktop: KDE
Display Server: x11
[CPU]
Vendor: GenuineIntel
Model: Intel(R) Core(TM) i3-3227U CPU # 1.90GHz
Physical cores: 2
Logical cores: 4
[Memory]
RAM: 3.7 GB
Swap: 0.0 GB
[Graphics]
Vendor: Intel
OpenGL Renderer: Mesa Intel(R) HD Graphics 4000 (IVB GT2)
OpenGL Version: 4.2 (Compatibility Profile) Mesa 22.2.0-devel (git-3e679219a1)
OpenGL Core: 4.2 (Core Profile) Mesa 22.2.0-devel (git-3e679219a1)
OpenGL ES: OpenGL ES 3.0 Mesa 22.2.0-devel (git-3e679219a1)
Vulkan: Supported
See https://askubuntu.com/a/98719
"Hard blocked" cannot be changed by software, look for a wifi toggle on your keyboard or edges of the laptop; the device can also be hard blocked if disabled in the bios.
And:
https://askubuntu.com/questions/98702/how-to-unblock-something-listed-in-rfkill#comment618926_98719
FYI hard block also happens when the wifi is disabled in the bios.
Related
We are experiencing performance problems with Stardog requests (about 500 000ms minimum to get an answer). We followed the Debian Based Systems installation described in the Stardog documentation and have a stardog service installed in our Ubutu VM.
Azure machine: Standard D4s v3 (4 virtual processors, 16 Gb memory)
Total amount of memory of the VM = 16 Gio of memory
We tested several JVM environment variables
Xms4g -Xmx4g -XX:MaxDirectMemorySize=8g
Xms8g -Xmx8g -XX:MaxDirectMemorySize=8g
We also tried to upgrade the VM with a machine but without success:
Azure: Standard D8s v3 - 8 virtual processors, 32 Gb memory
By doing the command: systemctl status stardog in the machine with 32Gio memory
we get :
stardog.service - Stardog Knowledge Graph
Loaded: loaded (/etc/systemd/system/stardog.service; enabled; vendor prese>
Active: active (running) since Tue 2023-01-17 15:41:40 UTC; 1min 35s ago
Docs: https://www.stardog.com/
Process: 797 ExecStart=/opt/stardog/stardog-server.sh start (code=exited, s>
Main PID: 969 (java)
Tasks: 76 (limit: 38516)
Memory: 1.9G
CGroup: /system.slice/stardog.service
└─969 java -Dstardog.home=/var/opt/stardog/ -Xmx8g -Xms8g XX:MaxD
stardog-admin server status :
Access Log Enabled : true
Access Log Type : text
Audit Log Enabled : true
Audit Log Type : text
Backup Storage Directory : .backup
CPU Load : 1.88 %
Connection Timeout : 10m
Export Storage Directory : .exports
Memory Heap : 305M (Max: 8.0G)
Memory Mode : DEFAULT{Starrocks.block_cache=20, Starrocks.dict_block_cache=10, Native.starrocks=70, Heap.dict_value=50, Starrocks.txn_block_cache=5, Heap.dict_index=50, Starrocks.untracked_memory=20, Starrocks.memtable=40, Starrocks.buffer_pool=5, Native.query=30}
Memory Query Blocks : 0B (Max: 5.7G)
Memory RSS : 4.3G
Named Graph Security : false
Platform Arch : amd64
Platform OS : Linux 5.15.0-1031-azure, Java 1.8.0_352
Query All Graphs : false
Query Timeout : 1h
Security Disabled : false
Stardog Home : /var/opt/stardog
Stardog Version : 8.1.1
Strict Parsing : true
Uptime : 2 hours 18 minutes 51 seconds
Knowing that there is only stardog server installed in this VM, 8G JVM Heap Memory & 20G Direct Memory for Java, is it normal to have 1.9G in memory (No process in progress)
and 4.1G (when the query is in progress)
"databases.xxxx.queries.latency": {
"count": 7,
"max": 471.44218324400003,
"mean": 0.049260736982859085,
"min": 0.031328932000000004,
"p50": 0.048930366,
"p75": 0.048930366,
"p95": 0.048930366,
"p98": 0.048930366,
"p99": 0.048930366,
"p999": 0.048930366,
"stddev": 0.3961819852037625,
"m15_rate": 0.0016325388459502614,
"m1_rate": 0.0000015369791915358426,
"m5_rate": 0.0006317127755974434,
"mean_rate": 0.0032760240366080024,
"duration_units": "seconds",
"rate_units": "calls/second"
Of all your queries the slowest took 8 minutes to complete while the others completed very quickly. Best to identify the slow query and profile it.
We have two hypervisor(Dell PowerEdge R630, virtualization environment: Proxmox), they are connected with an FC-switch and the FC-switch with the storage(dell compellent).
One of the hypervisor are connected via multipath to the storage and it's works.
The other hypervisor doesn't found the storage.
The not-finder-hypervisor says:
kernel: qla2xxx [0000:81:00.0]-001d: : Found an ISP2532 irq 93 iobase 0x00000000bf40f73b.
kernel: scsi host13: qla2xxx
kernel: qla2xxx [0000:81:00.0]-500a:13: LOOP UP detected (8 Gbps).
kernel: qla2xxx [0000:81:00.0]-00fb:13: QLogic QLE2562 - PCI-Express Dual Channel 8Gb Fibre Channel HBA.
kernel: qla2xxx [0000:81:00.0]-00fc:13: ISP2532: PCIe (5.0GT/s x8) # 0000:81:00.0 hdma+ host#=13 fw=8.07.00 (90d5).
kernel: qla2xxx [0000:81:00.0]-209e:13: SNS scan failed -- assuming zero-entry result.
The multipath module is loaded into kernel. Both hypervisor have the same loaded modules.
dm_multipath 28672 1 dm_round_robin
Check SAN-zoning and LUN-secuty on the array: they must define and allow host-connection with the array and LUNs on it.
Closed. This question does not meet Stack Overflow guidelines. It is not currently accepting answers.
This question does not appear to be about a specific programming problem, a software algorithm, or software tools primarily used by programmers. If you believe the question would be on-topic on another Stack Exchange site, you can leave a comment to explain where the question may be able to be answered.
Closed 4 years ago.
Improve this question
My new laptop has an NVIDIA graphics card (not sure which one). I have freshly installed Fedora 27. However, I cannot get my HDMI or VGA port to work or even be recognized. I've tried following the instructions at https://www.if-not-true-then-false.com/2015/fedora-nvidia-guide/ and https://fedoraproject.org/wiki/Bumblebee (as well as a few others), but have been unsuccessful thus so far.
Here is some output from various commands for context:
> xrandr -q
xrandr: Failed to get size of gamma for output default
Screen 0: minimum 1920 x 1080, current 1920 x 1080, maximum 1920 x 1080
default connected primary 1920x1080+0+0 0mm x 0mm
1920x1080 77.00*
> sudo lspci -v | grep -A 15 'VGA'
00:02.0 VGA compatible controller: Intel Corporation Device 591b (rev 04) (prog-if 00 [VGA controller])
Subsystem: Dell Device 07d1
Flags: bus master, fast devsel, latency 0, IRQ 255
Memory at eb000000 (64-bit, non-prefetchable) [size=16M]
Memory at 80000000 (64-bit, prefetchable) [size=256M]
I/O ports at f000 [size=64]
[virtual] Expansion ROM at 000c0000 [disabled] [size=128K]
Capabilities: [40] Vendor Specific Information: Len=0c <?>
Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00
Capabilities: [ac] MSI: Enable- Count=1/1 Maskable- 64bit-
Capabilities: [d0] Power Management version 2
Capabilities: [100] Process Address Space ID (PASID)
Capabilities: [200] Address Translation Service (ATS)
Capabilities: [300] Page Request Interface (PRI)
Kernel modules: i915
> sudo lspci -v | grep -A 18 '3D'
01:00.0 3D controller: NVIDIA Corporation Device 179c (rev a2)
Subsystem: Dell Device 07d1
Flags: bus master, fast devsel, latency 0, IRQ 255
Memory at ec000000 (32-bit, non-prefetchable) [size=16M]
Memory at c0000000 (64-bit, prefetchable) [size=256M]
Memory at d0000000 (64-bit, prefetchable) [size=32M]
I/O ports at e000 [disabled] [size=128]
Expansion ROM at ed000000 [disabled] [size=512K]
Capabilities: [60] Power Management version 3
Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [78] Express Endpoint, MSI 00
Capabilities: [100] Virtual Channel
Capabilities: [250] Latency Tolerance Reporting
Capabilities: [258] L1 PM Substates
Capabilities: [128] Power Budgeting <?>
Capabilities: [600] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?>
Capabilities: [900] #19
Kernel modules: nouveau
Any ideas?
It ended up being because I installed my OS in Basic Graphics Mode: https://ask.fedoraproject.org/en/question/46846/what-does-nomodeset-do/
I had an iOS iPad app crash and got the following crash log from the Devices tab:
Date/Time: 2017-10-13 15:06:22 -0600
OS Version: iPhone OS 11.1 (Build 15B5066f)
Architecture: arm64
Report Version: 26
Data Source: KPerf Lightweight PET
Kernel Cache: 0xffffffe000000000 1C4A9D92-74B9-1F20-096E-27915D7A6C03
Reason: Fence-hang-Vocab: 505ms handling fence, blown-fence (fence duration=505ms)
Command: Vocab
Path: /private/var/containers/Bundle/Application/9F4A7C15-D23E-46C8-B724-84C57D83B455/Vocab.app/Vocab
Identifier: com.mycompany.Vocab
Version: 1.4.0 (420)
Parent: debugserver [1467]
PID: 1469
Duration: 0.55s
Steps: 11 (50ms sampling interval)
Hardware model: J71AP
Active cpus: 2
Any insight into what this error is and what causes it?
According to this Apple Developer Forums Thread, one cause of blown fence errors is due to high memory pressure.
The developer of the app in question might be able to monitor memory pressure of the app, which could be a cause for the app being terminated.
Updated my xcode this evening to 7.2.1 im running on yosemite 10.10.5
i've just started learning swift, and everytime i try to run the simulator it crashes with the error:
could not load inserted library '/usr/lib/libignitor2.dylib' because no suitable image found.
I have spent the last 4 hours searching online, there seems to be a few similar errors of inserted library missing but nothing that i can see that helps with this error. The full code can be seen below.
Process: Simulator [2907]
Path: /Applications/Xcode.app/Contents/Developer/Applications/Simulator.app/Contents/MacOS/Simulator
Identifier: com.apple.iphonesimulator
Version: 9.2 (643)
Build Info: Indigo-643000000000000~28
Code Type: X86-64 (Native)
Parent Process: ??? [1]
Responsible: Simulator [2907]
User ID: 501
Date/Time: 2016-09-10 03:00:48.102 +0100
OS Version: Mac OS X 10.10.5 (14F1912)
Report Version: 11
Anonymous UUID: 1ACB9325-E877-4FA4-FEBD-B9450D15E13A
Time Awake Since Boot: 10000 seconds
Crashed Thread: 0
Exception Type: EXC_BREAKPOINT (SIGTRAP)
Exception Codes: 0x0000000000000002, 0x0000000000000000
Application Specific Information:
dyld: launch, loading dependent libraries
DYLD_INSERT_LIBRARIES=/usr/lib/libignitor2.dylib
Dyld Error Message:
could not load inserted library '/usr/lib/libignitor2.dylib' because no suitable image found. Did find:
/usr/lib/libignitor2.dylib: mmap() error 1 at address=0x107DE9000, size=0x00001000 segment=__TEXT in Segment::map() mapping /usr/lib/libignitor2.dylib
Binary Images:
0x107da0000 - 0x107dccff7 com.apple.iphonesimulator (9.2 - 643) <2A577F90-517C-3363-A980-EEB79D21FEBF> /Applications/Xcode.app/Contents/Developer/Applications/Simulator.app/Contents/MacOS/Simulator
0x7fff65635000 - 0x7fff6566b92f dyld (353.2.4) <708E385E-50C6-32A3-983C-42E97BEE4346> /usr/lib/dyld
Model: MacBookPro12,1, BootROM MBP121.0167.B14, 2 processors, Intel Core i5, 2.7 GHz, 16 GB, SMC 2.28f7
Graphics: Intel Iris Graphics 6100, Intel Iris Graphics 6100, Built-In
Memory Module: BANK 0/DIMM0, 8 GB, DDR3, 1867 MHz, 0x02FE, 0x4544464232333241314D412D4A442D460000
Memory Module: BANK 1/DIMM0, 8 GB, DDR3, 1867 MHz, 0x02FE, 0x4544464232333241314D412D4A442D460000
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x133), Broadcom BCM43xx 1.0 (7.15.166.24.3)
Bluetooth: Version 4.3.6f3 16238, 3 services, 27 devices, 1 incoming serial ports
Network Service: Wi-Fi, AirPort, en0
Serial ATA Device: APPLE SSD SM0128G, 121.33 GB
USB Device: Internal Memory Card Reader
USB Device: Bluetooth USB Host Controller
Thunderbolt Bus: MacBook Pro, Apple Inc., 27.1
Any help would be appreciated. thanks
You could try
sudo update_dyld_shared_cache -force
I'm trying to fix my beta but it appears to be trying to get after an update and this is the solution I"m working with. If it fails you can try
https://apple.stackexchange.com/questions/217232/trying-to-force-update-dyld-shared-cache-but-having-some-errors
I hope this is helpful