I use exec() function on cypress but I get timeout error sometimes even if it works properly.
Is there any possibility ignore this timeout error?
I do not want to see this error. I want to see always pass/true in any case.
You can look into failOnNonZeroExit options flag. It determines whether to fail if the command exits with a non-zero code.
cy.exec('some commands', { failOnNonZeroExit: false })
Or, You can also pass a timeout options object with cy.exec(), something like:
cy.exec('some commands', { timeout: 10000 }) //timeout for 10 seconds
Related
Since our test agents are slow some times- i am trying to add some additional time outs for some commands
I did it like using time out value on command as shown below.But its not respecting the value given
My understanding is cypress will wait for "10000" MS for getting the #Addstory element?
Can any one advice is this is the correct way please?
Thank you so much
cy.get('#addstory > .ng-scope').click({ timeout: 10000 })
In cypress.json file, increase the timeout to 10 seconds or what ever timeout you want like this: "defaultCommandTimeout": 10000 and save the file. Now close the app and open it again. Navigate to Settings > Configuration you should be able to see the new value set for defaultCommandTimeout.
I issue was i was adding time out on click not for getting the element when i changed like below -All good waiting for add story to be visible as i expected before click
cy.get('#addstory > .ng-scope',{ timeout: 10000 }).click()
I have a distributed Openwhisk setup, and when I execute a large number of functions simultaneously like this
wsk -i action invoke test -r -b
at some point instead of getting the actual result, I start getting the following message:
ok: invoked /_/test, but the request has not yet finished, with id
Any idea how I could force Openwhisk execute the function and still return the result regardless how long the invocation actually takes? Is there maybe some playbook variable responsible for timeout?
You can execute a function in non-blocking mode. In this case, you will get the activation ID immediately and function execution will happen in the background. You can then check/track the status of function execution with the activation ID.
Remove the "-b" option from the command.
Also, a function execution timeout is configurable (default 60s), if function execution requires more time to execute, you can define it while creating the function.
For per function limit you can specify below setting when creating the function.
-t, --timeout LIMIT the timeout LIMIT in milliseconds after which the action is terminated (default 60000)
So, in my collection I have about ten requests, with the last two being:
/Wait 10 seconds
/Check Complete
The first makes a call to the postman's echo (delay by 10 seconds) and the second is the call to my system to check for the status complete. Now, if status is unavailable I wait another 10s:
postman.setNextRequest("Wait 10 seconds");
The complete status on my system can appear in a minute or so. Now, as one can see - it is an infinite loop if something goes wrong with the system and status is never complete. Is there a way in postman/newman test to fail a test if it has been going for more than 2 minutes, for example.
Additionally, this will be executed in jenkins with command line, so I am not really looking into postman settings or delays between requests in the runner.
you may have a look to newman options here : https://www.npmjs.com/package/newman#newman-run-collection-file-source-options. The interesting option is
--timeout-request : it will surely fulfill your need.
In Postman itself, you may test the responseTime. I recall that there is a snippet, on the right part, which looks like this:
tests["Response time is less than 200ms"] = responseTime < 200;
and which could help you as the test fails if response does not occur within the requested time.
Alexandre
If you are going to be using Jenkins pipeline you can use the timeout step to cause long running jobs to result in failure, here's on for 2 mins.
timeout(120) {
node {
sh 'newman command'
}
}
Check out the "Pipeline Syntax" editor in Jenkins to generated your code block and look for other useful functions.
I'm using a gem to get code results from Ideone.com. The gem submits code to Ideone and then checks for the results page. It checks timeout times and then gives up if there's no result. The problem is it might give up too early, but I also don't want it to wait too long if there's not going to be a result. Is there a way to know when one should give up hope?
This is the relevant code:
begin
sleep 3 if i > 0
res = JSON.load(
Net::HTTP.post_form(
URI.parse("http://ideone.com/ideone/Index/view/id/#{loc}/ajax/1"),
{}
).body
)
i += 1
end while res['status'] != '0' && i < timeout
if i == timeout
raise IdeoneError, "Timed out while waiting for code result."
end
Sounds like you want to adjust sleep timeout and number of attempts parameters. There is no absolute values suitable for each case, so you should pick some which are most appropriate for you application.
Unfortunatelly the gem code have both this parameters (3 seconds delay and 4 attempts) hardcoded so you don't have an elegant way to change them. So you can either fork the gem and change its code or try to monkey-patch the value of TIMEOUT constant with http://apidock.com/ruby/Module/const_set . However you won't be able to monkey-patch the delay between attempts value without rewriting method .run of the gem.
FYI. Net::HTTP has their own timeouts - how much time to wait for ideone.com connection and response. If they are exceeded Net::HTTP raises Timeout exception. The setters are
http://ruby-doc.org/stdlib-2.0/libdoc/net/http/rdoc/Net/HTTP.html#method-i-read_timeout-3D and #open_timeout=.
In my application I want to terminate the exec! command of my SSH connection after a specified amount of time.
I found the :timeout for the Net::SSH.start command but following the documentation this is only for the initial connection. Is there something equivalent for the exec command?
My first guess would be not using exec! as this will wait until the command is finished but using exec and surround the call with a loop that checks the execution status with every iteration and fails after the given amount of time.
Something like this, if I understood the documentation correctly:
server = NET::SSH.start(...)
server.exec("some command")
start_time = Time.now
terminate_calculation = false
trap("TIME") { terminate_calculation = ((Time.now - start_time) > 60) }
ssh.loop(0.1) { not terminate_calculation }
However this seems dirty to me. I expect something like server.exec("some command" { :timeout=>60}). Maybe there is some built in function for achieving this functionality?
I am not sure if this would actually work in a SSH context but Ruby itself has a timeout method:
server = NET::SSH.start ...
timeout 60 do
server.exec! "some command"
end
This would raise Timeout::Error after 60 seconds. Check out the docs.
I don't think there's a native way to do it in net/ssh. See the code, there's no additional parameter for that option.
One way would be to handle timeouts in the command you call - see this answer on Unix & Linux SE.
I think your way is better, as you don't introduce external dependencies in the systems you connect to.
Another solution is to set ConnectTimeout option in OpenSSH configuration files (~/.ssh/config, /etc/ssh_config, ...)
Check more info in
https://github.com/net-ssh/net-ssh/blob/master/lib/net/ssh/config.rb
what I did is have a thread that's doing the event handling. Then I loop for a defined number of seconds until channel closed.If after these seconds pass, the channel is still open, then close it and continue execution.