Table title with outreg2 - latex

Question

I am working with the community-contributed command outreg2 to export regression estimates from a logit model to LaTeX.
Is there a way to show the table reference/label, for example, "Table 1: Some Title"?
I cannot seem to be able to do this using outreg2:
logit v1 v2 v43, or
outreg2 using "table", label cti(odds ratio) eform tex replace ctitle(Logit)
With esttab, using \label in the title option to get the desired result works:
esttab using "Table.tex",tex eform label replace title("Logit"\label{tab1})
Any suggestions?
EDIT:
Note that even when i do the following:
outreg2 using "table", label cti(odds ratio) eform tex replace ///
ctitle(Logit) title("Logit"\label{tab1})
This only produces the following:

Answer 1

Consider the following toy example:
webuse lbw
logit low age lwt i.race smoke ptl ht ui, or
Both esttab and outreg2 produce the same result when their title() option is used:
esttab, tex eform label replace title("Logit"\label{tab1})
outreg2 using "table", tex label cti(odds ratio) eform replace title("Logit"\label{tab1})
However, this will not work when typesetting as outreg2 produces
different markup than esttab.
The way to do what you want with outreg2 is to run the following from Stata:
outreg2 using table, tex replace label cti(odds ratio) eform
Unlike esttab, the outreg2 command does not have an option to insert markup
directly from within Stata. Thus you will have to add the markup below manually:
.
.
.
\begin{table}[htbp]\centering
\caption{Logit \label{tab1}}
.
.
.
\end{table}
.
.
.
The produced tex file should then look as follows:
\documentclass[]{article}
\setlength{\pdfpagewidth}{8.5in} \setlength{\pdfpageheight}{11in}
\begin{document}
\begin{table}[htbp]\centering
\caption{Logit \label{tab1}}
\begin{tabular}{lc} \hline
& (1) \\
VARIABLES & odds ratio \\ \hline
& \\
birthweight<2500g & \\
& \\
age of mother & 0.973 \\
& (0.0355) \\
weight at last menstrual period & 0.985** \\
& (0.00682) \\
race = 2, black & 3.535** \\
& (1.861) \\
race = 3, other & 2.368** \\
& (1.040) \\
smoked during pregnancy & 2.518** \\
& (1.009) \\
premature labor history (count) & 1.719 \\
& (0.595) \\
has history of hypertension & 6.250*** \\
& (4.322) \\
presence, uterine irritability & 2.135* \\
& (0.981) \\
Constant & 1.586 \\
& (1.910) \\
& \\
Observations & 189 \\ \hline
\multicolumn{2}{c}{ seEform in parentheses} \\
\multicolumn{2}{c}{ *** p$<$0.01, ** p$<$0.05, * p$<$0.1} \\
\end{tabular}
\end{table}
\end{document}

Answer 2

Leaving this here for future reference.
Actually, if you add the option tex(fragment) to outreg2, the resulting file will only contain the tabular environment. Then, you can create the table environment, with the caption that you desire, and use \input only to replace the tabular environment.