I'm using a dedicated server on aruba with ZyWall firewall. I have two ports listening in the server, using telnet from inside I can connect to both the ports. If I try to telnet from outside I can access only to one of them.
I have not internal firewall, and I don't understand how I can see if the ZyWall is blocking the port access or it is forwarding all connections to that port to another ip.
Have you any suggestion?
I found the solution. I accessed the firewall web interface from a firefox installed in the dedicated server behind the firewall (the web interface is not accessible from outside), then I made two steps:
I added a rule on which I permit the access to the target port. I made this using the "Service" tab in the Security->Firewall menù.
In the matrix between LAN, WAN, DMZ etc.. I modified the rule "from WAN to LAN" and I added the rule made in the previous step.
Now it works!
Related
I have a little server in my local network that provides several web services. Each service can be accessed by entering the ip of the server followed by the respective port.
Now I always have to remember which service is behind which port and it would be nicer to have specific subdomains forwarded to these ports. For example
ip:1234 -> foo.server.local
ip:4321 -> bar.server.local
How can this be done? I have pihole running on the server and had hoped to get this done using pihole but I was not successful.
What you are looking for is to set up a Domain Name Server (DNS). phoenixnap.com/kb/raspberry-pi-dns-server This guide should help.
You use a domain to direct to an IP:port combo. Like you could direct 123.12.12.12:8080 to some.thing and 123.12.12.12:8081 to any.address.
The domain name is arbitrary and masks the whole IP:port address.
I'm trying to connect to my public IP http://34.125.119.106:8080/, where I have a Jenkins service running but I can't and don't know why.
I've create firewall rule to allow tcp traffic on port 8080, which is the port exposed to Jenkins, but I still cannot connect. I looked into the /etc/default/jenkins file, to see if everything inside was configured correctly. I tried to line in this file like 'HTTP_HOST=127.0.0.1', like some people advise to do ,but it doesn't work for my case. Does anyone know how to solve this?
Sorry for my bad English.
enter image description here
i made a test and it successfully connected,but i still cant connect to my external Ip
Use the default settings, because HTTP_HOST=127.0.0.1 locks you out:
HTTP_HOST=0.0.0.0
HTTP_PORT=8080
HTTPS_HOST=0.0.0.0
HTTPS_PORT=443
Listing to all interfaces with 0.0.0.0 is fine, but HTTP_PORT should be -1.
As a first step my recommendation is to check if your service is exposed and through what port number. For this you can use command sudo netstat -plntu. You should be looking for an output similar to:
tcp6 0 0 :::8080 :::* LISTEN 17917/java
If its not, change your /etc/default/jenkins file to port 8080
After that from inside your GCP project, you can run a connectivity test having as source one of the IP addresses you are using to reach your Server and as destination your Servers VM instance IP address. This test will simulate traffic and tell you where it's getting stuck whether if it's stuck on the way to your Server or if your server is not correctly configured. You can get a good reference in this document.
If you have already configured your ingress firewall rule, just make sure its applied to your VM, it sometimes happens that you have a network tag on your VM instance and another tag on your firewall rule.
I'm running a FTB Revelation server on my Synology-NAS and I can connect in the intranet, but when my friends or I want to connect with my public-ip, they can't connect.
A portforwading tester says, that the port is closed.
I'm using a fritzbox and my ports are opened.
What could be the problem?
I had this issue too. You probably need to call your Internet Provider and ask if you have a dedicated IP. Port forwarding for ipv4 only works with dedicated IPs.
You can use NGROK (https://ngrok.com/) to "bypass" port forwarding, but server's IP will change every time you restart NGROK, and you will not be able to see player's true IPs in the server (You will see, for example, 0:0:0:0:0:0:0 instead of 93.22.22.22)
I am using Windows 10 with IIS 10.0
I am publishing website on IIS and I need to reach it with public ip.
What I did;
* Port forwarding through router
* Adding DMZ with my local IP
* Turning off firewall
* Adding port to firewall inbound rules with allow edge traversal
I can connect with internal IP like 192.168.1.75:81
I get "System.Net.Sockets.SocketException A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond from [MYPUBLICIP]" when I try to reach it like MYPUBLICIP:81
What are the possible scenarios that blocks to port?
Thanks.
As far as I know, the error message means there is no server listening at specified ip/port that you are trying to connect to.
In my opinion, you should firstly make sure your client machine could access your server by using this MYPUBLICIP address.
Then I suggest you could try to make sure the port 81 is your IIS web application port.
Besides, I suggest you could try to open your event viewer to find out the details error message.
I'm trying to set up a VM instance in Google Compute Engine. So far so good.
Now I've installed ajenti, which requires port 8000 for its web interface.
I created a firewall rule for TCP 8000. It doesn't work. I also set up iptables on the server to try to fix the problem. It ![still doesn't work]. I'm kind of desperate right now. I just want to access the web interface.
Thanks for help!
Firewall Rule
By default SSL is enabled in Ajenti. Try accessing your web page using https://YOURSERVERIP:8000
The target tag you have set restricts which instances the firewall rule applies to. Ensure that your instance has the http-server tag.