I want to put a figure and the TOC side by side in one slide where it would look like
TOC Figure
I have tried to include them each in a minipage respectively and then put them both in a figure environment. But the result does not look good, for the TOC is formatted as a paragraph, instead of an itemize look. So, does anybody have a better solution? Thanks in advance.
PS
I use beamer for creating slides.
Have you tried the following:
\frame{
\begin{columns}
\column{.5\textwidth}
\tableofcontents
\column{.5\textwidth}
\begin{figure}[h]
\centering
HERE-FIGURE
\caption{Testfigure}
\label{fig:a}
\end{figure}
\end{columns}
}
That worked just fine for me.
Related
How do I create this in Latex? I tried $r^e_{\_}$ or $r^e\_$ but none give the variable as shown in the added picture.
You can move the underscore up a bit with
\documentclass{article}
\begin{document}
$r^{e}_{\raisebox{0.21em}{\_}}$
\end{document}
I would like to know how to make a point above a symbol (ie : αΊ‹)
I tried \overset{.}{x}, but the point is very small...
Can you help me ?
Thanks
Just to write down one answer, elaborating a bit the source cited in the comments, and to add the following minimal codes.
\documentclass{article}
\begin{document}
$\dot{x}$
$\ddot{x}$
\end{document}
One dot (\dot) and two dots (\ddot) work in math mode as above. Three dots (\dddot) and four dots (\ddddot) the same but they require the package amsmath:
\documentclass{article}
\usepackage{amsmath}
\begin{document}
$\dddot{x}$
$\ddddot{x}$
\end{document}
Instead in text mode, the package called stackengine may help:
\documentclass{article}
\usepackage{stackengine}
\begin{document}
\stackon[1pt]{x}{.}
\end{document}
I'm new to LaTex and I wanted to know how I can change the Margins of my scrreport so that the chapter title, text and basically everythin starts a bit higher and ends a bit lower. In my opinion there is too much empty space before anything starts.
If I use this simple example:
\documentclass[12pt,a4paper,twoside]{scrreport}
\usepackage{blindtext}
\begin{document}
\chapter{First Chapter}
\blindtext
\end{document}
I think the margins from top and bottom are too big. So i want everything to move up a little bit.
Thanks!
Method 1:
Choose one of the predefined layouts. You'll find a list of available options in the koma script documentation.
\documentclass[12pt,a4paper,twoside,DIV=15]{scrreport}
\usepackage{blindtext}
\begin{document}
\chapter{First Chapter}
\blinddocument
\end{document}
Method 2:
Setting up the text area manually. You should be really sure that you know what you are doing to get an aesthetically pleasant result.
\documentclass[12pt,a4paper,twoside]{scrreport}
\areaset[current]{168.00mm}{250mm}
\usepackage{blindtext}
\begin{document}
\chapter{First Chapter}
\blinddocument
\end{document}
So i'm trying to hide the label in my cover image.
>\begin{figure}
>\center
>\includegraphics[scale=0.5]{universidade}
>\caption* {Mycaption}
>\end {figure}
This way it's not labeling the figure but its not showing on the list of figures
Help please ;D
You can give the caption package the option labelformat=empty to suppress the Figure 1 etc. labelling:
\usepackage[labelformat=empty]{caption}
You can use square brackets to specify the description for the figure list, and curly brackets for the actual figure caption. So I think you should be able to do the following to supress the caption but still have an entry in the figure list:
\begin{figure}
\center
\includegraphics[scale=0.5]{universidade}
\caption[Mycaption]{}
\end {figure}
There are a couple of options, depending on what yo're after exactly:
\documentclass{article}
\usepackage{graphicx}
\setcounter{topnumber}{3}% Just for this example
\begin{document}
\listoffigures
\begin{figure}
\addcontentsline{lof}{figure}{Example image A}%
\centering
\includegraphics[height=4\baselineskip]{example-image-a}
Example image A
\end{figure}
\begin{figure}
\addcontentsline{lof}{figure}{\protect\numberline{}Example image B}%
\centering
\includegraphics[height=4\baselineskip]{example-image-b}
Example image B
\end{figure}
\begin{figure}
\centering
\includegraphics[height=4\baselineskip]{example-image-c}
\caption{Example image C}
\end{figure}
\end{document}
The figure caption is added using \addcontentsline{lof}{figure}{<caption>}, where <caption> can either contain a blank \numberline{}, or just the regular caption. The above example shows the usage of either.
It would also be possible to have no label shows in the image, but have a numbered entry in the LoF using caption. But it would seem strange to have a numbered entry in the LoF and an unnumbered figure.
I'd like to insert a picture (figure) into a document which is using a two-column layout. However, I want it to take one whole page and not be centered on one of the columns. Currently if I add a [p] modifier to the figure, the whole image lands on the last page, instead in the middle of the document.
How can I force one page to switch back to a single-column layout and insert a single big picture there?
Use the figure* environment. So instead of
\begin{figure}[ht] % I typically use ht
\centering
...
\end{figure}
you should use
\begin{figure*}[ht]
\centering
...
\end{figure*}
This also works for tables (i.e. table*).
Consider this link for more information
It is not elegant, but with float package loaded you can use:
\begin{figure}[H]
\onecolumn\includegraphics{arc}
\end{figure}
\twocolumn
But you have to place this piece of code to exact locetion in source code. Otherwise you'll get pagebreak anywhere in twocolumned page, then page with image image.
To supplement #Crowley's answer, to avoid pagebreak after implementation.
Instead of using \twocolumn, use this package instead \usepackage{multicol}.
Then,
\begin{multicols}{2}
\section Write or place anything you want
\end{multicols}
This works for me!
\usepackage{multicol} in your preamble.
Then
\begin{document}
\begin{multicols}{2}
blah blah blah text
\end{multicols}
\begin{figure}[H]
\includegraphics[width=1\textwidth]{arc}
\end{figure}
\begin{multicols}{2}
blah blah blah text
\end{multicols}
\end{document}
This is ugly, and dirty. and you will need to fiddle with where you figure is in order to get the text balanced, but it is exactly what you asked for.