In v13, we can choose internal transfer and then fill destination_journal_id and make transfer.In v14, how to make transfer between two journal.
Related
I'm trying to design a system where streams (backed by an external service, ex. an azure queue storage) may be added or removed dynamically. When a new stream appears, a set of cooperating agents are created to handle this new data stream.
All samples seems to statically configure the available streams (at startup). Is there a way to add and remove streams dynamically?
Sure. You can subscribe and push to any stream without the need to create it explicitly upfront, much in the same way as with virtual actors - the stream will be created (activated) on the first use
I have a system with multiple subsystems communicating with CANOpen. There is a main unit with a screen (for men-machine interface and stuff) and sub-units for minor operations(like sample button status, manage power, take measurements...).
We defined a CANOpen based communication protocol for this system. Subsystems share their conditions periodically with TPDO messages and do stuff according to main unit's commands sent with RPDO messages. And also some NMTs are in use too.
So I've been asked to add a new command to this protocol, zeroize. This command shall be sent broadcast and it shall cause everybody to delete softwares. What is the right way to do this?
Maybe I can use a RPDO? Are we allowed to define new NMT commands in CANopen? Maybe I can do it with NMT but by using a new commandt hat is not in use already?
Thanks in advance
Ip.
It is a bit confusing what you mean with TPDO and RPDO since the main unit's TPDO is going to be the peripheral units' RPDO and vice versa. But yes, the correct way to send out some custom broadcast message would be with a PDO.
Although, depending on what you mean with "delete software", CANopen might provide a mean for it. There are the save (OD 1010h) and load (OD 1011h) registers in the object dictionary. Save is to be used for the purpose of storing all CANopen communication (PDO configuration, mapping etc) in non-volatile memory. And load is used to restore CANopen parameters to factory defaults. These should however not be used to save/load application-specific settings.
You are not allowed to define new NMT commands.
Objects 1010h and 1011h can be used to reset the values in the object dictionary. If you really want to delete the software, the firmware upgrade protocol from CiA 302-3 might help. Writing 00h (Stop program) followed by 03h (Clear program) to object 1F51h sub-index 1 on the slave will delete the application. Whether it's actually "zeroed out" depends on the implementation. You'll need two SDO requests per slave for this though. The standard specifies that object 1F51h cannot be PDO mapped. Although that requirement may not be enforced for your devices, in which case you could achieve broadcast "zeroing" with two PDOs.
I'm currently using the dataAPI to keep the dataitems synchronized between handheld and wearable.
Still I want to make sure that every data is stored and there is no data lost in the process.
I'm currently reading GPS parameters when the wear is not connected to the handheld and when they connect, they sync the dataitems.
How reliable is DataAPI?
Is my idea of creating a local file doubling my effort?
How can I create a local file on my wear device and then access it?
Syncing data using DataApi is reliable and I recommend using that; if you come across a scenario that sync is not happening reliably, that should be considered a bug and needs to be reported as such. One issue that folks run into is that they create the same data item and they don't get the onDataChanged() callback but that is by design, if the very same data is being added multiple times, there is no change, hence no callback triggers.
Another factor you might want to consider is whether the data you create on one node is for consumption by all other nodes or only a targeted one; DataApi syncs data across all connected nodes so if I create a data item on watch1 and want to sync that with my phone and if there is a watch2 in the picture as well, watch2 also gets the same data.
If you end up using the DataApi, I strongly recommend to make sure to put in place a policy that removes the data once it is synced and consumed otherwise data will be accumulated with no supervision and you'll finally run out of space.
To answer your questions:
I don't know how reliable it effectively is, but we had problems where data updates didn't trigger the appropriate listeners on the watch side. So I'm not sure. Maybe someone has an official statement for this?
I think it depends on the amount of data you want to store. So I suggest you first become clear about the amount and then choose the format. Keep in mind that there is also the possibility to store data in the Shared Preferences.
These guys here tried to save an image on the watch, but that makes no difference wheter it is an image file or text or whatever file.
Newbie question.
I will need to have a data base from about 200 UIImages (single of them less than 500kb size) for iPad app. Customer want to have possibility to change set of this images from time to time without releasing new version of app in appstore and app must work without connection to the web (local data base on a device). I don't see how this can be done simultaneously, I see only one common option here:
Image data base would be stored on a server, what app customer will be able to change anytime. User will need to have web connection and every time he will start the application - existing data base will load into the app.
Main questions here:
is it possible to update data base on user's device without releasing new version of app and what data base managing system is more proper to this situation(SQLite, MySQL etc...)?
Q : is it possible to update data base on user's device without releasing new version of app?
A : Yes. It is possible.
SQLite will be perfect for you.
The photographs reside on the web server.
A number of start-off photographs may reside within the boundle so that the app is not really empty at start.
However, when downloading the app, the user must be online. In most cases he would still be online directly afterwards when he launches the app for the first time.
The server provides two services:
A quick one that just provides a version number of the
photo-database content and/or the date of the last change to the
photographs on the server.
The app frequently (not more than daily I would say) checks wether there are new images on the server or not.
If they are then the user is asked, whether he wants to download them.
If the user says YES then the app sends the version number and/or last date and/or IDs of all local photographs to the server and the
server provides the information about which photographs have been
added and where to download that very photograph and which have to
be deleted.
Then you add or delete or update the photographs from the download source given by the server. (That may well be an URL to the
very same server of course.)
For 200 data sets I would strongly suggest core data with SQLite - the standard stuff.
You may then think of holding the image data in the file system or in NSData properties within the database.
Helo,
I need to create a new project where there is a long and complex transaction chain
(User registers, uploads documents, sends physical goods, money transfers, etc).
There are many possible branchings in these steps and each includes multiple steps (item sent, in transit, on destination, etc, etc).
Is there a framework (Ruby or otherwise) I can use to easily create & maintain such a complex chain ?
Sounds like the perfect task for a State Machine. It can handle the states of an entity (ordered, paid, shipped, etc.) and you can define what should happen during state transitions.